Coriolis Flow Transmitter RHEONIK

Inside the measuring sensor, there are precision tubes that are energized by an electromagnetic drive system, which itself is fed by the transmitter, to vibrate at their natural frequencies. When a liquid or gas flows through the vibrating tubes, it is subjected to additional deflection due to the degree of inertia that is generated. This deflection is recorded electronically by two velocity sensors and a high-precision electronic time delta. This measured quantity is proportional to the mass flow rate.

A further conversion into physical units is done in a purely digital manner using a signal processor in the transmitter. At the same time, all of the appliance’s functions are constantly monitored. Should any disruptions occur, all of the errors that have occurred are immediately reported in the display.

rhe08The transmitter has a 4 to 20 mA analogue output with programmable span, which is proportional either to the measured mass flow rate or the temperature; it also has an impulse output that supplies mass-proportional impulses. All of the outputs and measuring functions can be verified at any time by the user by using the diagnostic mode in the appliance. The maintenance or new calibration intervals can be monitored via a run-time counter. For service or repair purposes, the transmitter and flow sensor can be replaced independently of each other.

rhe12This significantly reduces the costs of spare parts for the installed flow sensor/transmitter. During the factory calibration, the mass flow sensor can be calibrated independently of the transmitter. All sensor-specific calibration data can be programmed using magnetic switches located on the front panel. To achieve this, the instrument does not need to be opened. All of the relevant data is buffered in a non-volatile semiconductor device (EEPROM).

The RHEONIK mass flow meter consists of one of the RHM series flow sensors and one RHE series transmitter. The remote unit RHE 07/08 is for installation in a safe non-Ex area and is connected to the sensor via a single multi-conductor cable. Please note, that the types RHE 07/08 and all sensor articles are available in non Ex-versions (without Exnameplate). The RHE 11 (Ex d) may be installed and operated in hazardous Ex-areas (Zone 1 or 2). Ex-series sensors RHM (with Ex-Label) are, when connected with an Ex- Transmitter, made for installation inside hazardous areas (Ex-zone 0, 1 or 2). The transmitter RHE includes seven printed boards which can be replaced during servicing. The remote electronic unit consists of two bent measuring loops in the shape of an omega.

Kind of Coriolis Flow Transmitter

  • RHE 07

The RHEONIK mass flow meter consists of one of the RHM series flow sensors and one RHE series transmitter. The remote unit RHE 07/08 is for installation in a safe non-Ex area and is connected to the sensor via a single multi-conductor cable. Please note, that the types RHE 07/08 and all sensor articles are available in non Ex-versions (without Exnameplate). The RHE 11 (Ex d) may be installed and operated in hazardous Ex-areas (Zone 1 or 2). Ex-series sensors RHM (with Ex-Label) are, when connected with an Ex- Transmitter, made for installation inside hazardous areas (Ex-zone 0, 1 or 2). The transmitter RHE includes seven printed boards which can be replaced during servicing. The remote electronic unit consists of two bent measuring loops in the shape of an omega.

  • RHE08

The RHEONIK mass flow meter consists of one of the RHM series flow sensors and one RHE series transmitter. The remote unit RHE 07/08 is for installation in a safe non-Ex area and is connected to the sensor via a single multi-conductor cable. Please note, that the types RHE 07/08 and all sensor articles are available in non Ex-versions (without Exnameplate).

  • RHE11

The RHE 11 (Ex d) may be installed and operated in hazardous Ex-areas (Zone 1 or 2). Ex-series sensors RHM (with Ex-Label) are, when connected with an Ex- Transmitter, made for installation inside hazardous areas (Ex-zone 0, 1 or 2). The transmitter RHE includes seven printed boards which can be replaced during servicing. The remote electronic unit consists of two bent measuring loops in the shape of an omega.

  • RHE12

The RHE 12 transmitter is equipped with a 24 VDC mains supply. For trouble-free operation, the power supply must maintain the specified nominal voltage of +- 10%. When connecting the transmitters, always ensure that the power supply is switched off. The earthing for the power supply should be connected using the relevant RHE earthing.

  • RHE14

The  RHE14  is  low  cost,  compact  and  ideal  for  OEM applications. I/O includes 4-20mA, pulse, flow direction and RS232 serial data. Programming and configuration by SensCom™ software. The RHE06 is ATEX approved for hazardous area installation  and  offers  pulse  output  and  Error  and  Flow Direction.  *The  RHE06F+  has  double  pulse  outputs with 90° phase shift for custody transfer applications

Model and type of Corilois Mass flow Sensor
Small Size coriolis Mass Flow Sensor

ideal for embedded systems and precise small flow applications

  1. RHM 015 Low Flow Mass Flow Meter flow rate <0.6 kg/min
  2. RHM 02 Low Flow Mass Flow Meter flow rate <2 kg/min
  3. RHM 03 Low Flow Mass Flow Meter flowrate <5 kg/min
  4. RHM 04 Low Flow Mass Flow Meter flow rate <10 kg/min
  5. RHM 06 Low Flow Mass Flow Meter flowrate <20 kg/min
  6. RHM 08 Low Flow Mass Flow Meter flow rate <50 kg/min
Medium Size coriolis Mass Flow Sensor

Suited to industrial and process flow control and monitoring

  1. RHM 12  Mass Flow Meter flow rate <100 kg/min
  2. RHM 15  Mass Flow Meter flow rate <200 kg/min
  3. RHM 20  Mass Flow Meter flow rate <300 kg/min
  4. RHM 30  Mass Flow Meter  flow rate  <750 kg/min
  5. RHM 40  Mass Flow Meter  flow rate  <1500 kg/min
Large Size coriolis Mass Flow Sensor

Perfect for material movements in small and wide scale operations

  1.  RHM 60 Coriolis Flow Meter flow rate <3000 kg/min
  2.  RHM 80 Coriolis Flow Mass  Meter flow rate <8000 kg/min
  3.  RHM 100 Coriolis Flow Mass Meter flow rate <12000 kg/min
  4.  RHM 160 Coriolis Flow Mass Meter flow rate <30000 kg/min

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s